Search Beat Jump
Turns the SEARCH buttons (◀◀ / ▶▶) or the TRACK SEARCH buttons into beat jumps. UTILITY → SEARCH BEAT JUMP: OFF (stock buttons) / 1 / 2 / 4 / 8 / 16 / 32 / 64 BEATS, and UTILITY → BEAT JUMP BUTTONS: SEARCH (default) / TRACK SEARCH (both saved). A press jumps that many beats back or forward; holding repeats the jump (every 500 ms at first, then every 100 ms). The other button pair is unchanged.

- Player
- Pioneer CDJ-2000NXS2, firmware 1.87
- On the deck
- UTILITY → SEARCH BEAT JUMP, BEAT JUMP BUTTONS
- Needs
- Nothing else: works on its own.
- Known limits
- The stock beat jump rules apply: no jump near the start or end of the track, loops move instead of jumping (up to 4 beats), and below 80 BPM jumps above 8 beats are refused.
- 32- and 64-beat jumps use sizes the stock firmware has but never offered.
- The player keeps 45 to 50 seconds of the track decoded ahead (stock 25 to 30) so that long forward jumps land while playing; after one long jump the next waits until the player has read ahead again. The history kept behind the playhead (back jumps, reverse) is about 70 seconds instead of about 90.
- In a beat mode the chosen buttons no longer scan or change track; set SEARCH BEAT JUMP to OFF for the stock behaviour.
Changelog
- v1.2.0Latest
- UTILITY > SEARCH BEAT JUMP: 64 BEATS.
- The player keeps 45 to 50 seconds of the track decoded ahead (was 25 to 30), so 32- and 64-beat jumps forward land while playing (64 beats never did, 32 only sometimes). After one long jump the next waits until the player has read ahead again.
- v1.1.2
- UTILITY > SEARCH BEAT JUMP: the stock setting is now labelled OFF (it was DEFAULT); same behaviour and saved value.
- v1.1.1
- Fix: with BEAT JUMP BUTTONS = TRACK SEARCH the buttons could stop jumping after a long set until the player was restarted, while SEARCH kept working. TRACK SEARCH presses are now read the same way as SEARCH presses and no longer go through the stock track-search logic, which ignores the buttons in some states (for example when the player runs low on message buffers). In a beat mode TRACK SEARCH now never changes track.
- Fix: the settings are now saved without touching the stock record format (Utility byte 6 bits 4-6). In 1.0.0-1.1.0, saving SEARCH BEAT JUMP = DEFAULT or 1 BEAT made the next boot reset some stock UTILITY settings and bring the size back as 2 BEATS.
- If SEARCH BEAT JUMP shows 2 BEATS after updating and you had DEFAULT, set it back once; it now stays.
- Tested in the emulator, including TRACK SEARCH with the stock refusal forced (1.1.0 ignored the buttons, 1.1.1 jumps), and against the stock journal code; not yet on a deck.
- v1.1.0
- UTILITY → BEAT JUMP BUTTONS: SEARCH (default, as before) / TRACK SEARCH, saved. The other pair stays stock.
- The size row is renamed SEARCH BEAT JUMP (same choices). Settings saved by 1.0.x carry over (buttons: SEARCH).
- Tested on a deck.
- v1.0.1
- Tested on a deck: marked stable. The firmware is identical to 1.0.0.
- v1.0.0
- Beat jumps now on the SEARCH buttons (◀◀ / ▶▶) instead of TRACK SEARCH; TRACK SEARCH is stock again.
- UTILITY → SEARCH: DEFAULT / 1 / 2 / 4 / 8 / 16 / 32 BEATS, saved; fresh decks start at DEFAULT.
- Holding SEARCH repeats the jump (every 500 ms for the first four, then every 100 ms).
- v0.1.0
- First release (experimental): the TRACK SEARCH buttons as beat jumps.